Lightweight Insulating Concrete Information

Lightweight Insulating Concrete Roof Systems, (LICRS)

The lightweight insulating concrete roof installation system have a long and proud history of over 60 years that began in the northern United States. At that time, building codes requiring fire resistant thermal barrier provided by lightweight insulating concrete roof decks helped to meet this new need. Today there are hundred of thousands of successful lightweight insulating concrete decks installed in North America and around the world.

Overview

Lightweight insulating concrete roof systems offer the unique opportunity to remove water from the roof. The ability to design custom slope to drain conditions and then have the plan followed in the roof construction sets these systems apart from rigid insulation systems. However to take advantage of this opportunity requires a large number of designs that are very difficult to create by hand drawing methods.

Design parameters for the roof slope layout

A proprietary computer program has been developed that allows the following roof top conditions to vary to produce the optimum design. The program considers the following variables for each design.

Installation

Can be installed over non-slotted or slotted galvanized corrugated metal decks, structural concrete substrates and, where appropriate, over existing roofs in recover applications. It is not intended for use in extremely hot, dry climates. ICRDS excellent fire resistance properties make it cost effective versus the more expensive alternative of adding a fireproof coating to the deck`s underside, as required by most systems incorporating conventional rigid insulation board. The lightweight concrete is placed at a minimum 2-inch thickness over the top of the EPS (expanded polystyrene foam).

How much does ICRDS cost?

Cost-effective lightweight Insulating Concrete Systems varies in price by geographical area and by application requirements. Your LCS sales representative will be glad to assist you with budget numbers and binding quotations for our products and services.

How do you increase the R-value of LWIC?

The R-value of any LWIC is increased by adding expanded polystyrene insulation board during application of the LWIC. A LWIC system (LWIC plus EPS insulation) can easily achieve 50 R`s for the installation.

What is the equilibrium moisture content of cellular concrete?

The equilibrium moisture content of cellular concrete is typically 14%-18% by weight.

When can LWIC be roofed?

Roofing may begin 2-4 days after placement. The base sheet fastener should attain a minimum 40-pound withdrawal value.

How resistant to weather is LWIC?

After a LWIC deck is roofed, it is highly resistant to weather conditions as has been demonstrated for over 60 years of continuous applications in all geographic areas of theUnited States and in other parts of the world.

If EPS is in place and a threat of rain exists, what is the best procedure to follow?

Place the slurry coat so that the bond holes are full of material. It is not necessary to slurry coat the board surfaces. A slurry coat on the board is acceptable for next day topping without any special treatment such as a bonding agent.

What types of roof membranes can be installed over LWIC?

Built-up Roofing, Modified Bitumen, and Single Ply Membranes of various approved compositions have been successfully installed over LWIC.

How far can cellular concrete be pumped?

Cellular concrete is a very easily pumped, highly fluid mixture. The bulk of cellular concrete is placed by pumping. Cellular concrete typically will move through the pump lines using less pressure than typical heavier grout mixes. Documentation of cellular concrete being pumped up to and exceeding 500 ft. vertically and 10,000 feet horizontally is commonly available. This is also dependent on the contractor`s equipment capability.

Are control joints needed for thermal movement in a LWIC system?

No.

What is an acceptable finish for LWIC?

A surface finish free of ridges and protrusions is an acceptable finish for roofing application. Most LWIC is left to self-seek a level and not surface &%3B finished &%3B in the traditional sense. Much cellular concrete is covered by another material. A floor overlayment type smoother tool can be used simply to break the surface air cells and create a more uniform and polished look to the surface in the rare case when a more uniform surface appearance is desired.

Featured Product Overview
SmartBIM Objects available for download BIM Objects
ManuSpec 3-part specs available for download MANU-SPEC 3-part Specs
SpecData datasheets available for download SPEC-DATA Datasheets
Technical Datasheets
03 00 00 - Concrete
04 00 00 - Masonry
05 00 00 - Metals
08 00 00 - Openings
09 00 00 - Finishes
10 00 00 - Specialties
11 00 00 - Equipment
12 00 00 - Furnishings
21 00 00 - Fire Suppression
22 00 00 - Plumbing
23 00 00 - HVAC
26 00 00 - Electrical
27 00 00 - Communications
31 00 00 - Earthwork
33 00 00 - Utilities
34 00 00 - Transportation